-
December 13th, 2004, 08:46 PM
#11
Inactive Member
That's the pulley I'm using. I will let you know when I finally get my car running.
-
December 13th, 2004, 09:48 PM
#12
Senior Hostboard Member
The 3.4" pulley will make about 10 psi on a stock crank-pullied D16Z6.
-
December 13th, 2004, 10:07 PM
#13
Inactive Member
Actually never mind. The 3.4" pulley is 5-rib (b-series) and it doesn't fit. I just tried to put it on and it hit my fender wall.
-
December 13th, 2004, 10:30 PM
#14
Inactive Member
Which reminds me...
Still got that stock pulley Tad? Looks like I'm desperate now. $45 shipped. I can paypal you instantly.
<font color="#a62a2a" size="1">[ December 13, 2004 06:31 PM: Message edited by: JRciv ]</font>
-
December 14th, 2004, 09:08 AM
#15
Inactive Member
Sigh... Payment sent [img]redface.gif[/img] .
Yeah, I couldn't believe it when it didn't fit. I was finally going to finish the install today - just drop in the blower and hook up the lines. It blows my mind how tight the tolerances are with that charger.
Just keep me updated. I need that pulley ASAP! I'm tired of riding a stupid motorcycle to and from work [img]graemlins/thumbs_down.gif[/img] .
-
December 14th, 2004, 04:23 PM
#16
Inactive Member
P.S. about the 3.4" pulley:
thanks for the info, 10lbs is too much for me.
i want 9lbs at the most. 8-9 would be fine either way, 8 would be nice for peace of mind, but alil extra pull from 9 would be cool
10 is scary though, and too close to the SC being out of it's efficiency range.
About my FS pulley:
heehee,
I knew you'd be back!
yeah the guys at JR said that they tried as hard
as they could to get a 4rib working on the 96+ but it just wouldnt fit, so they had to go with 3rib,
no way a 5rib is gonna fit.
and yes I still have it.
paypal me at [email protected]
i'll send it out tomorrow [img]smile.gif[/img]
Funny thing is I was just going to start throwing it up on some classifieds again. I let it sit as I was busy just getting my SC working.
-
December 14th, 2004, 05:33 PM
#17
Inactive Member
thanks man,
I got the money,
check your email about my other pulley fs [img]wink.gif[/img]
-
December 21st, 2004, 01:53 AM
#18
Inactive Member
Ok, so does JR have a supercharger pulley
available the will give me 8-9psi??
sohc 92-95 civic?
-
December 21st, 2004, 04:23 PM
#19
Senior Hostboard Member
Tad,
I lied. The 3.4" blower pulley will give you 8-9 psi... I said 10 psi above, however, I was confused as to which pulley was the stock size for a D16Z6 JRSC kit. Since the stock kit comes with a 3.8" blower pulley, the 3.4" pulley would add approximately 2 psi more boost.
I hope that helps... and by the way, I believe I have a 3.4" pulley on the shelf... give me a call at the shop.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks