-
December 7th, 2007, 09:17 PM
#11
Inactive Member
After thinking about it, it occurred that without gluing/securing the horn panels into a solid, unitary mass, won't you gobble up a good portion of the horns gain in shaking the individual panels...(i.e. energy lost to the gasket)?
Further thought...isn't one of a rubber gasket's primary functions absorbtion of vibration to reduce the transmission of sound?
<font color="#FFFFFF" size="1">[ December 07, 2007 05:40 PM: Message edited by: bfish ]</font>
-
December 8th, 2007, 03:28 AM
#12
Senior Hostboard Member
Originally posted by bfish:
I've played with lots of gasket solutions........
<font size="2" face="Verdana, Helvetica, sans-serif">Greets!
Neoprene ANSI flange gasket material is ideal for repeated closures at high pressure, it's what's used in harsh environment equipment enclosures. I've removed my 515 baffles dozens of times over the decades to rotate the drivers, which as you've experienced still seal well: http://www.mcmaster.com/ pg. 3352.
GM
-
December 8th, 2007, 02:45 PM
#13
Senior Hostboard Member
Originally posted by bfish:
Funny how only a few years removed from hands-on wrenching has restricted my vision........
<font size="2" face="Verdana, Helvetica, sans-serif">I know the problem well, 'use it or lose it' as they say. Wouldn't this material require too much clamping pressure for wood construction though?
Anyway, how you been? I sent several emails awhile back, but haven't seen any comebacks. Have you had a chance to look at the HK and/or Sony yet?
GM
-
December 8th, 2007, 04:01 PM
#14
Inactive Member
Yeah, I'm thinking of the red, fiber-reinforced material we used to use in hot/chilled water pipe flanges. Tough stuff indeed.
<font color="#FFFFFF" size="1">[ December 08, 2007 08:24 PM: Message edited by: bfish ]</font>
-
December 8th, 2007, 05:42 PM
#15
Inactive Member
Yeah, the material (as we used it) used 5/8" flange bolts torqued to 50 ft/lbs...Granted though, it had to hold 100 psi at 90 degrees delta T.
<font color="#FFFFFF" size="1">[ December 08, 2007 08:23 PM: Message edited by: bfish ]</font>
-
December 8th, 2007, 11:52 PM
#16
Senior Hostboard Member
Thanks for the gasket ideas gents.
I finished the wedge base/top pieces today.
Anyway to cut out a pattern in plywood you
need a jig saw.
Cut as close as possible to the finished curve as you can safely... 1/8 -> 1/16 is fine.
You also need a router and a router bit with a ball bearing guide
Then just go slow, using one cut out piece as a guide for the rest: Wedge Base pieces
Next is to cut out the angled wedge pieces which will require a little more work than this 'cos the side angle changes.
-
December 8th, 2007, 11:55 PM
#17
Senior Hostboard Member
Hey bFish....provide links to your pictures, don't embed images...that's why I opened this new thread...that is unless it's Brazilian supermodels...then it's alright.
-
December 9th, 2007, 01:58 AM
#18
Inactive Member
Sorry...
<font color="#FFFFFF" size="1">[ December 08, 2007 10:08 PM: Message edited by: bfish ]</font>
-
December 9th, 2007, 02:06 PM
#19
Senior Hostboard Member
Originally posted by GM:
Neoprene ANSI flange gasket material is ideal for repeated closures at high pressure, it's what's used in harsh environment equipment enclosures. I've removed my 515 baffles dozens of times over the decades to rotate the drivers, which as you've experienced still seal well: http://www.mcmaster.com/ pg. 3352.
GM
<font size="2" face="Verdana, Helvetica, sans-serif">Nice, ...good website, I ordered some last night, thanks for this link Greg.
-
December 9th, 2007, 02:50 PM
#20
Senior Hostboard Member
Originally posted by bfish:
Sorry...
<font size="2" face="Verdana, Helvetica, sans-serif">Where'd she go? She looked too perfect to be real.
<font color="#FFFFFF" size="1">[ December 09, 2007 10:52 AM: Message edited by: GM ]</font>
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
This forum has been viewed: 21015457 times.
Bookmarks