Printable View
Here are my pics hours after installing the new suspension set-up. DON'T MAKE FUN OF MY HUBS, I TOOK THEM OFF http://www.hostboard.com/ubb/smile.gif
------------------
91 Si:
-K&N drop-in
-Tokico HP sturts(blue)
-Weapon R circut pro's
WHAT'S BODY ROLL???
http://albums.photopoint.com/j/Album...095&a=14008942
------------------
91 Si:
-K&N drop-in
-Tokico HP sturts(blue)
-Weapon R circut pro's
WHAT'S BODY ROLL???
kewl. i love the si w/ a lowered look.
you like the bonus handling, eh?
------------------
-Ben L.
1989 Civic Si
1990 300ZX TT Stage III
I love how it handles now!! It is pretty bumpy, but I might not have cut the bumpstops enough to be that low, so in a while I will fix for ride comfort.
**Now I just have to replace my axles so I don't get the lovely "KNOCK, KNOCK, KNOCK" on left hand turns, it get really annoying, really quick.
Thanks for the comment http://www.hostboard.com/ubb/biggrin.gif
------------------
91 Si:
-K&N drop-in
-Tokico HP sturts(blue)
-Weapon R circut pro's
WHAT'S BODY ROLL???
looks good man,
i took the bumperstops out of mine and it doesnt work. it's still bumpy as hell, but i dont have the money for new shocks yet, so i have learned to like it http://www.hostboard.com/ubb/biggrin.gif
------------------
| |JEFF| |
Team: Decepticon Racing
1990 Civic Hatchback Si (Black)
http://members.cardomain.com/90civicrider
http://members.shaw.ca/c90civicrider
Kill List:
1999 Honda Civic CX (cold air intake)
1995 Chevorlet Camaro (ecu chip)
1993 Mazda mx3 GS (stock)
1992 Acura Integra RS (stock)
1991 Nissan 240sx SE (stock)
1989 Honda Prelude SR (exhaust)
1989 Chrysler Dynasty (stock)
1988 Honda Prelude S (stock)
eh, i take it not as "bumpy" but "increased road feel" http://www.hostboard.com/ubb/smile.gif my car is a little bumpy but i love that tight feel rather than a slushy lincoln towncar feel like you're riding in a bathtub.
------------------
-Ben L.
1989 Civic Si
1990 300ZX TT Stage III
Well, when I took off my factory struts I tested them, 3 out of the 4 where completely shot! So even though it's a little bummpy, I love how I have no more ROLL!! It is only bummpy on really ruff roads or on those brick cross walks. That might be my axles and CV joints?? "KNOCK" "KNOCK" http://www.hostboard.com/ubb/frown.gif I NEED CASH!!
THANKS
------------------
91 Si:
-K&N drop-in
-Tokico HP sturts(blue)
-Weapon R circut pro's
WHAT'S BODY ROLL???
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by POS_91Si:
Well, when I took off my factory struts I tested them, 3 out of the 4 where completely shot! So even though it's a little bummpy, I love how I have no more ROLL!! It is only bummpy on really ruff roads or on those brick cross walks. That might be my axles and CV joints?? "KNOCK" "KNOCK" http://www.hostboard.com/ubb/frown.gif I NEED CASH!!
THANKS
<HR></BLOCKQUOTE>
Tell me if the cutting the bumpstops more stops the bouncing. My circuit pros bounce like mad even on my KYBs
------------------
1991 Civic 4dr
ZC-blown head gasket
Zdyne Ecu
Si tranny
Thermal R&D exhaust
Iceman
Chikara header
Weapon R Circuit Pro
KYB AGX's
Powerslot Rotors
AEM/Nissin Pads
Going B16--very soon
How low are ya?? I am only 1" below factory now, but in the pic I was slammed as far as I could go without getting any camber, and it was pretty bouncy!! I noticed when I put the rear up a little, it didn't do it so bad. But how can you go wrong with 0 body roll?? Do you have min. body roll?
**P.S. 91zc Is your Thermal R&D the classic cat-back?? If so how deep and low is it really, do you like it a lot?? I really like their(TRD) tips!! GOOD LUCK WITH YOUR HEAD GASKET!
------------------
91 Si:
-K&N drop-in
-Tokico HP sturts(blue)
-Weapon R circut pro's
WHAT'S BODY ROLL???