-
well....driving home from work last Tuesday approaching my exit, my car started to decel on its own. Just having installed the MSD 6aL i'm thinking the negative coil wire i had to tap into(drilled a tiny hole in distributor cap i made) was getting shorted out. Under accelloration the car seemed fine. Well this all happened within a 1/4 mile from my exit. Getting on the offramp i coasted. came to the bottom of the ramp and the car never started again. I'm thinking....ut oh...starter or fuel pump. I thought different things due to it not turning over at all....and my fuel pressure gauge was pegged. anywho....had to have my car towed a few miles. After tearing it apart...this is what i found out.
Set screw for my rotor backed itself out. Locked up the rotor...locked up the distributor...locked up some big ass lift Spec B intake cam which proceded to rip about 6" of timing belt teeth out. everything advanced. result?
distributor bearings ticking, timing belt, bent valves, leaking rings. bearings worn. I know the last 3 because i have metal grit and gas in my oil...and my compression test resulted in 220,210,190,210. We can hear number 3 tapping. So?
i ran the car this past weekend and the friggin car still put out 13.295 @102.49mph. crazy
moral of the story? make sure that set screw is tight.
------------------
Lip
94' GSR-R?, 13.20 @ 102.83mph. 12's in da Spring or bust...i can smell it now!!
-
WOW man sorry to hear on the misfortune.
Be careful on those specs http://www.hostboard.com/ubb/smile.gif and that is a strong sucker you got there http://www.hostboard.com/ubb/biggrin.gif
Good to hear it's still doing well.
-
http://www.hostboard.com/ubb/eek.gif
13.2 on a fugged up all-motor beast aint too bad Lip! http://www.hostboard.com/ubb/biggrin.gif
I think I am going to check my set screw tonight.
------------------
Mark - Darth Boost - Turbo Mafia
98 Pearl Black GS-R, DRAG Gen. 3 Turbo
13.2 at 114MPH (GTech/Pro w/Drag Radials)
-
Sorry to hear that Lip. Time for a built bottem end and higher compression.
Kyle
-
Dude that sucks!!!.....you know most people cant get that screw to come out...and end up cutting it out...and yours comes out on its own...what luck!! http://www.hostboard.com/ubb/frown.gif
------------------
John
Hey what you got in there??(In a redneck voice)
Oh just a Intake, Header and Exhaust :D
B18C1 powered Civic EX Coupe
'92 Civic VX Hatch...being prepared for MAD BOOST!
-
you didn;t even mention how many times the f$%^&&% MSD cap had to be taken off ... the moral of the story, don;t listen to manufacture instructions all the time ...
yeha lip, 13.2 ain;t bad ... maybe a lil laxative wooda brought it down to 13.1, huh ?
Greg
------------------
94 Civic FROG
435HP/289 lb-ft. torque.
11 Second Club.
-
I had problems w/that screw too, i ran w/o for some time, nothing happened but my timing was all over the place. u going to rebuilt the engine? again?
Did anyone beside me notice that whenever a Honda engine goes bad, its always cyl. #3?
-
I hear because #3 is the last one to get fuel, and sometimes comes up short.
-
it's because #3 is the weakest after the car was running, i.e. it runs the hottest since it gets fired between 2 cylinders, #2 and #4
Greg
------------------
94 Civic FROG
435HP/289 lb-ft. torque.
11 Second Club.
-
but isnt the firing order 1-3-2-4, so #3 would fire before the two cyliders that are next to it (2 and 4).
The intake runner to #3 certainly isn't the longest.
And since #2 is one of the middle cyliders, wouldn't that make it as vorunable as #3? or even more considering the fact that #4 fires right before it?
-Kamil
[This message has been edited by EEinteg (edited July 07, 2000).]
