-
-
I don't know where you can get Bando belt...actually I would careless what kind of belt since they have to be replaced at around 15K anyways...or whenever I see it begin chewing off...
But with Endyn stepper pulley, don't you need a 630mm? Would 640mm be too big?
------------------
It's powered by GASOLINE damnit!!!
-
They normally should have the conversion charts from one brand belt to another even if they only carry one brand.
------------------
"There's nothing wrong with the car except that it's on fire."
-
I have the same problem... "You mean Bondo?" http://www.hostboard.com/ubb/smile.gif Anyway, the equivalent belts are frequently a different size (within +/- 5mm) of the "Bando" belts... on my RS, I had an "equivalent" but it was too long and I ended up scraping my blower pulley on my idler pulley... bring the belt w/ you so you can make sure the sizes are in the ballpark.
Chuck
------------------
96 Integra B18B w JRSC@9psi, JR BTC, JR MAP Converter, Walbro 342, DC 4-2-1, DC Catback, ST Rear Swaybar, etc.
Best 1/4: 14.66 @ 94.7
-
Tony I put a gates belt on mine the had the original size but not sure about the longer one for you. Napa has the gates belts. Later
------------------
-
Friggin backwoods rednecks here dont even have a CONVERSTION TABLE!! F-it, i went to BANDOAMERICAN.com and pulled up a list of distributors. There is one here in MARYVILLE.
Guy at ADVANCE AUTO PARTS said,"Well, if you bring me any belt, i can match it perfectly to that size." Well, duh, they can teach MONKEYS to do that?! Jesus Christ..... http://www.hostboard.com/ubb/rolleyes.gif
------------------
1996 Acura Integra GSR, JRSC@9psi, Drag raced WEEKLY, Autocrossed MONTHLY, and ALWAYS DAILY DRIVEN! [email protected] in the 1/8th, shootin for 8.3's with the 9psi and M/T's!
-
Beware. Gates belts and Bando belts are different sizes, even though the precious conversion charts say they're the same. Pep boys will exchange a new (Dayco) belt for the next size if you have a fitment problem. I found the Dayco sizes to be the same as Bando.
------------------
-
hmm dayco works fine. dang guys my bando after 18k miles got all its ribs chewed up for 5 inches along the belt! and pieces missing here and there.
------------------
Houston, TX
1999 FBP Civic EX auto SUPERCHARGED Performance: Jackson Racing Supercharger w/fuel pump
Air Intake w/ Hiper Filter, Heat Shield Thermal Research & Development Cat-Back Exhaust, Accel Thundersport +300 Plug wires, Nuespeed Sport Springs, APC Rear Strut Tower Bar, APC Breather Filter, VTEC Light
www.geocities.com/tom_civic99
-
What exactly is the size required for a 99civic si kit with the endyn stepper pulley? I asked larry and was simply told, "16mm longer" ... lots of help that is.
------------------
-
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by kannon:
What exactly is the size required for a 99civic si kit with the endyn stepper pulley? I asked larry and was simply told, "16mm longer" ... lots of help that is.
<HR></BLOCKQUOTE>
The guy can be a jerk sometimes...I bought the pulley from him..and emailed him asking what belt size would I need for my GSR. He told me "to go the part store, take the old belt with me and match it up with a longer one that fits..."
WTF was the guy thinking??? Take off my belt, and walk to the auto store to find a belt??? From where I live, it'll take me a day to get there...
So politely emailed him stating that I don't have a ride, and i live quite far away from the shop...He replied with three words: "get a friend"...
------------------
It's powered by GASOLINE damnit!!!
