-
Well on the way home i finally played with the vtec crossover points.
Current setting: 2500RPM vtec crossover. I have not seen any part throttle det. that I was seeing before. In fact the only time the J&S seen knock was about 2600rpm in 4th gear. (rush hour and i did not notice what gear i was in) I tried flooring at various RPM points in VTEC 2500+rpm no knock on the J&S. Part throttle same thing i am just about 100% knock free.
The car is now very responive with the VTEC crossover that low. I was surprised to say the least. I excepted the car to bog but it did not once. It would seem that the car *really* likes VTEC that low with the SC. I know that it did not like it with the car n/a. The car took right off( a little to good for rush hour). The butt dyno gives it two cheeks up!!!
I will monitor it over the next couple of days and see what happens but it looks good so far. Just think VTEC all the time!!!
If anybody has any questions about my set up or wants me to try anything just let me know.
k
------------------
Project Dark Side is Here!!!
JRSC 8psi, Walbro HP pump, MSD BTM, J&S, STR rail, etc...
-
Wow, cool finding! http://www.hostboard.com/ubb/biggrin.gif
Did you also richen up the mixture at that rpm point? What are your fuel settings? Thanks.
-
a/f gauge reads three greens and i have not changed any fuel setting on the fields. I am currently running 14BTDC 3/4degree retard/psi on the BTM and base FP at 66psi.
gas mileage: we will see in a week of driving like this!
k
------------------
Project Dark Side is Here!!!
JRSC 8psi, Walbro HP pump, MSD BTM, J&S, STR rail, etc...
-
You mean that you got rid of the tip-in detonation that I get around 3k-4k. Did you still have it with the btm installed (but no fields)? I have been reluctant to buy anything but I might have to get one. Please keep us posted.
------------------
95 Civic SOHC VTEC,JRSC,255HP fuel pump,RC 240cc,Split Second A/F meter,Greddy exhaust,Ground Controls,Tokico Illumina,rear ST swaybar,Nuespeed f&r upper bars,GAB lower f bar,f&r camber adjuster,Powerstop rotors w/ Porterfield pads
-
Save your money and buy a V-AFC from APEXi. The electronics are 10 times better on the APEXi unit. The fields unit is ok but the problem is that the electronics are not consistent. You should be able to make the same amount of horse power with the unit off as when the unit is on all zero settings. After testing on the dyno the car actually lost power on all zero settings. Plus the settings on it are non-variable. With the V-AFC the settings are throttle dependent. So at part throttle regular driving it is actually possible to get better gas mileage out of your car while realizing the power gains at WOT. Something to think about.
-
Oh another thing with the regular S-AFC (non vtec version of the V-AFC), on a fully built LS turbo, we reached 350bph on the dyno on pump gas!!!! Call 949-457-1234 for more details on that.
-
Yeah I really like the V-AFC, Jim is selling these and they are going on the blackbird motor's. Really good tunability and ability to record runs so you can actually see if it helped or hurt your performance! http://www.hostboard.com/ubb/smile.gif
Will
------------------
13.24 on a smokin' motor can't be bad!?!
-
I think the fuel setting on the field are kind of well bad. But two years ago when i bought it is was the only thing goin!
Question: does the v-afc have *ALL* the fuel settings of the s-afc. Cause if it does i think that it is a slam dunk then to buy one. If not it i will prob. buy the s-afc for fuel tunning!!!.
Civicboy: yes the btm is hooked up and it was still there with the BTM. and yes i am not seeing the tip-in det. once in VTEC.
------------------
Project Dark Side is Here!!!
JRSC 8psi, Walbro HP pump, MSD BTM, J&S, STR rail, etc...
-
1fstGSR
...doesn't the rising pressure of the FMU make it hard to tune the V-AFC? Meaning that with the FMU, and varied driving, the settings will be "jumping around". If you keep the FMU that is. http://www.hostboard.com/ubb/biggrin.gif
------------------
1998' 4dr GSR, 8psi JRSC w/hand ported plenum, Walbro HP fuel pump, valves set to .005i/.006e, MSD BTM, B&M CommandFlo regulator(working it out), stock intake w/resinator cut off at fenderwell for "cool air", Greddy sp exhaust, Tokico Illumina 5-ways, Neuspeed springs(sux!), Skunkworks 22mm rear swaybar, ES motor mounts and front swaybar bushings, Yokohama AVS 205/50/15's, Metal Master brake pads(KVR Carbon Fibre pads sitting on work bench) ,B&M fuel pressure gauge, Autometer sport comp A/F gauge in dimmer location...
and awaiting my YLW 00' ITR due in late March!!!
Honest officer, I had no idea how fast I was going...the speedometer only gos to 150...
-
sounds interesting.
Wonder what your gas mileage will be at that setting?
