-
Here are my pictures as I promised. The .wav files are on mylaptop at home so we'll have to update that later on.
http://www.geocities.com/silvino_oro...ed_pistons.htm
------------------
Silvino Orozco http://www.geocities.com/silvino_orozco 221HP/161TQ at the wheels - corrected)
'97 Integra GS-R (13 degrees timing) w/JRSC (8 PSI), DC 4-2-1 Ceramic Headers, Walboro 255lph High pressure fuel pump , AEM Cold air intake, Powerstop rotors/Axxis Metal Master brake pads, A'PEXi Dunk Exhaust, J&S Safeguard unit,NeuSpeed rear Swaybar, Eibach Springs, Clutch Masters Stage III clutch (not in dyno run), AEM cam gears (installing soon), Energy Suspension motor mounts (not in dyno run), MSD 6BTM (set to .5 timing removed per lbs of boost), MSD Blaster Coil SS
[This message has been edited by Silvino (edited March 21, 2000).]
-
Eeewwww...looks bad. I can't wait for your WAV files though.
-
Way too hot! You must have driven it a lot after the problem set in. Most times detonation will leave the pistons a lot cleaner than those. The crud is probably baked oil.
It looks to have some exiting the exhaust in that first picture. Good for killing mosquitos, but bad for the pocketbook.
I feel for you big time. Shit like that isn't any fun.
-
Sil, this damage looks just like Will's... only he had a single piston erode instead of two. This is long-term leaning out... primarily caused by long-term high RPM running (You wouldn't be guilty of any high-altitude street racing would you ???). Your piston tops don't look bad at all (color and deposits)... I think you did a good job of minimizing the damage. Inspect the rods when they come out: if any are really dark in color, they have been compromised.
Lastly, post a picture of the head - a close-up of cylinders 3 and 4... I want to see the valves and chambers.
------------------
'93 Civic Si H/B with B18C1, JRSC @ 8psi
Best 1320: 12.68 at 110 mph
-
Wow, that was creepy symbolism... I am talking about the death of your motor in post number "187" !!!
Again, Sil... My heart is heavy for you and your car.
------------------
'93 Civic Si H/B with B18C1, JRSC @ 8psi
Best 1320: 12.68 at 110 mph
-
More pics of the head and valves coming soon. I'm sorry i didn't do it sooner but I've been busy at work between planning this rebuild and getting on here http://www.hostboard.com/ubb/smile.gif
------------------
Silvino Orozco http://www.geocities.com/silvino_orozco 221HP/161TQ at the wheels - corrected)
'97 Integra GS-R (13 degrees timing) w/JRSC (8 PSI), DC 4-2-1 Ceramic Headers, Walboro 255lph High pressure fuel pump , AEM Cold air intake, Powerstop rotors/Axxis Metal Master brake pads, A'PEXi Dunk Exhaust, J&S Safeguard unit,NeuSpeed rear Swaybar, Eibach Springs, Clutch Masters Stage III clutch (not in dyno run), AEM cam gears (installing soon), Energy Suspension motor mounts (not in dyno run), MSD 6BTM (set to .5 timing removed per lbs of boost), MSD Blaster Coil SS
-
What exactly causes this to happen?? I want to have the same mods done to my car, what do you think the problem was and what can be done to avoid it??
sorry about the stupid questions just curious?!!
thanks
nick
------------------
95 GSR 4-DR w/minor bolt-on looking for boost!
-
If you've read through the threads on this incident, you will know there were a few factors. The critical factor was that FUEL was coming up short, period. This is why JRCIVIC and others are developing a fuel replacement to be safer and gain power. The two other major factors were that the J&S sensitivity was turned nearly off and the 6BTM was also not retarding timing (I set both this way to see what would happen). This incident was avoidable without the fuel fix but who knows. I still blame my setting things VERY risky for this happening. Basically, don't f' around at 8 PSI. Stick with what's been safe or watch out.
------------------
Silvino Orozco http://www.geocities.com/silvino_orozco 221HP/161TQ at the wheels - corrected)
'97 Integra GS-R (13 degrees timing) w/JRSC (8 PSI), DC 4-2-1 Ceramic Headers, Walboro 255lph High pressure fuel pump , AEM Cold air intake, Powerstop rotors/Axxis Metal Master brake pads, A'PEXi Dunk Exhaust, J&S Safeguard unit,NeuSpeed rear Swaybar, Eibach Springs, Clutch Masters Stage III clutch (not in dyno run), AEM cam gears (installing soon), Energy Suspension motor mounts (not in dyno run), MSD 6BTM (set to .5 timing removed per lbs of boost), MSD Blaster Coil SS
-
Wow. I love your wav file, until you blow up your engine http://www.hostboard.com/ubb/frown.gif. Would you mind if I post it on my web site ? By looking at your pistons, I pretty sure that you haven't melted them in that run only, they were probably melted slowly overtime. Stock piston don't handle heat as much as aftermarket one. Pay for the extra heat coating for your new ones.
------------------
To 24 PSI, and beyond !
HS Le Club
-
When you get it apart, can you get some close-up pics of the cylinder walls, rings, lands, and piston crown?
Thanks
Matt
