-
Hey Guys, long time no see. I`m back and building a jrsc`d b18c. I`m going to go ahead and do sleeves, pistons, and rods while the motor is being pieced together. My question is, what compression are you guys running? I don`t want to run a ton of boost, maybe 8lbs, so I`m thinking 9:1 might be a bit low. With a built block, I think I would be fine around 10:1. I might run a 60 shot on it down the road, too. Any thoughts on this?
Ryan
------------------
Sc`d S2000
ls/vtec CRX
& a monster truck to pull`em with
www.HondaClub.com
-
Why are you planning on running such low boost with all the upgrades? Lowering your compression will definetely help if you plan on running higher boost (10+ PSI), but are you sure it's really worth your time and money to only boost 8PSI?
------------------
Go ahead, try your luck, its just a 4 door family car
-
I`m going to road race it which is a lot of abuse (Yes, the cooling sytstem is in check). Plus, I`d rather spend a few extra bucks and do everything correct the 1st time. I don`t want to tear the block apart a few months down the road.
Ryan
------------------
Sc`d S2000
ls/vtec CRX
& a monster truck to pull`em with
www.HondaClub.com
-
I'm about to have my car back. And I've fully built the motor, (rods, pistons, valves, etc) It is a B18C1 in a 96 GSR 4 door. It's been resleeved with full ductile iron sleeves and bored 3mm over, which makes the discplacement 1933cc. The compression ratio that I went with is 10:1. I did this for a lot of various reasons. For one, boosting a large amount (13-16psi) with a JRSC creates a LOT of heat. So I plan on boosting a moderate amount (9-12psi) but I'm keeping the compression the same as stock so that I will not loose any power. There are others on this board that have lowered thier compression and tried to boost higher with not so good results. Also increasing the discplacement lowers the boost pressure "seen" by the motor. So with the setup that I'm going to have (CRV + 3.8) I will not see the typical 13 or more psi. I will probably be around 10-11.
Anyway, I don't know for sure if it will kick ass or not till I get it on the dyno and see what kind of numbers it puts down. I should have some numbers by the end of this month, or early next month. So you then can see if the higher compression works or not, without being the guinee pig yourself. http://www.hostboard.com/ubb/smile.gif
------------------
96gsr 4door w/ a big hole where the motor is supposed to be!
Current daily driver = 88 civic LX hybrid JDM B16A5 - 1/4...14.6 @ 94
-
Sounds like you and I have a simillar setup. My block is at Golden Eagle as we speak so we`ll see who`s the Guniea Pig =)
------------------
Sc`d S2000
ls/vtec CRX
& a monster truck to pull`em with
www.HondaClub.com
-
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by vtecvoodoo:
Sounds like you and I have a simillar setup. My block is at Golden Eagle as we speak so we`ll see who`s the Guniea Pig =)
<HR></BLOCKQUOTE>
Well man I wish you luck. I really hope it goes well with your motor... esp since you have a similar setup as mine! http://www.hostboard.com/ubb/biggrin.gif What kinda HP numbers are you thinkin you'll get?? Also are you boring your's out big?
------------------
96gsr 4door w/ a big hole where the motor is supposed to be!
Current daily driver = 88 civic LX hybrid JDM B16A5 - 1/4...14.6 @ 94
-
84mm =)
------------------
Sc`d S2000
ls/vtec CRX
& a monster truck to pull`em with
www.HondaClub.com
-
anybody else?
------------------
Sc`d S2000
ls/vtec CRX
& a monster truck to pull`em with
www.HondaClub.com
-
Will you be my valentine? http://www.hostboard.com/ubb/biggrin.gif
------------------
1995 Milano Red GSR
H/A & H/T Teg Forum Mod
The darkside is the only side!!!
-
Of course, Cack ! !
When you coming out here?!?
------------------
Sc`d S2000
ls/vtec CRX
& a monster truck to pull`em with
www.HondaClub.com
-
I thought before March, but the way work is going, who knows!
Im hoping for a Spring Break trip over there. If thats the case...get them grilles over @ Norm Reeves cookin brotha http://www.hostboard.com/ubb/biggrin.gif
------------------
1995 Milano Red GSR
H/A & H/T Teg Forum Mod
The darkside is the only side!!!
-
The Grilles at my place are burnin` every weekend!
------------------
Sc`d S2000
JRSC`d b18c EK HB (50% finished)
ls/vtec CRX
& a monster truck to pull`em with
www.HondaClub.com
