Results 1 to 7 of 7

Thread: FMU's

  1. #1
    Inactive Member sullust's Avatar
    Join Date
    July 12th, 2001
    Posts
    86
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Question

    Ok, I need some help here. What is a FMU used for? I have a fuel pump that keeps up with the demand whether or not i'm on boost, so what else remains to be done with an FMU? I don't even know what the hell FMU stands for.

    I'd appriciate some help on this.

  2. #2
    Inactive Member 97SCGS's Avatar
    Join Date
    April 17th, 2001
    Posts
    72
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Fuel Monitor Unit, it works with the FPR to raise and lower fuel pressure for boosted cars.

    ------------------
    RevHard-2
    T3/T04E Turbo,Spearco 30" IC,Tial Wastegate,Vortech BOV,Apex-i S-AFC,Thermal 3"Catback,3"test pipe,Greddy turbo timer,BBK 62mm TB,Walbro FP,RC 310's,B&M S.Shifter,Magnecor wires,NGK plugs,CS stage2 clutch

  3. #3
    Inactive Member sullust's Avatar
    Join Date
    July 12th, 2001
    Posts
    86
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    what benefit is gained from an FMU? if your fuel pump is strong enough so that you don't run lean on boost, why do you need an FMU?

  4. #4
    Inactive Member newt2's Avatar
    Join Date
    November 16th, 1999
    Posts
    68
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Without an FMU you're either going to run waaaay to rich to even idle correctly on the low end or dangerously lean on the high end. Your ECU doesn't see boost, and wouldn't know what to do about it if it could. The only way to get more fuel under boost is to have a boost sensing device that can increase fuel to the engine.

    As far as I know you can't run boost on a Honda without either an FMU or a standalone ECU. Every turbo or SC kit that I know of comes with a basic one, and there are better aftermarket ones out there too.

  5. #5
    Inactive Member Peyomp's Avatar
    Join Date
    December 11th, 2000
    Posts
    190
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    FMU is Fuel Management Unit. It is a marketing word for FPR, or Fuel Pressure Regulator, which does what it says. Boost FMU/FPRs are used to raise fuel pressure for boost. They add a certain amount of extra fuel pressure per pound of air pressure the compressor on your engine adds (be it an eaton blower, a turbo, etc). The only way to not use one is to get a standalone engine management system, and some big ass injectors.

  6. #6
    Inactive Member sullust's Avatar
    Join Date
    July 12th, 2001
    Posts
    86
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    ok. so the people that have had their JR FMU's stick were they talking about the FMU that came with the JRSC kit, or another FMU that JR offers?

  7. #7
    Inactive Member Sonnyballs's Avatar
    Join Date
    January 12th, 2001
    Posts
    460
    Follows
    0
    Following
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Quoted
    0 Post(s)

    Post

    Actually, the Greddy turbo kit does not use an FMU. It uses an FCU (more marketing hype! tongue)

    The kit comes with 310cc injectors and controls fuel by manipulating the MAP sensor voltage.

    It's a decent alternative, but this approach limits how much boost you can run.

    Sonny

    ------------------
    Sonny Van Hook ([email protected])
    2000 Supercharged Civic Si @ 6psi
    1999 Tonykart/Honda 80cc Shifter

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •